Customer Care Representatives
(888) 276-4666

                    

 

 

ONSITE HP PRINTER REPAIR   

HP Printer Repair

 

Create On-site Service Appointment Online

You're invited to fill our form below and someone from our Customer Care Group will contact you to confirm the service appointment. You may also fill out form to ask technical question or make comments.


Required fields**

 

FOLLOW US ON SOCIAL MEDIA

Onsite Printer Repair Printer Repair Laserjet Printer Repair HP Color Laserjet Printer Repair

Navigation

repair my printeret s

ervice

hp printer repair

hp service

hp printer service

hp service center
fuser error
 
 

Numerical printer messages
When resolving printer messages, perform all listed actions in the order until the message is resolved.

Numerical printer messages

Control panel message Description Recommended action

10.XX.YY SUPPLY10.XX.YY SUPPLY  MEMORY ERROR or 10.XX.YY SUPPLY MEMORY ERROR For help press
The printer canot read the electronic information (e-label) on the print cartridge in order to keep track of the page count for the print cartridge.
XX Description
    00 memory error on the cartridge
    10 memory device not found
YY Description
    00 black print cartridge

1 Open the top cover, remove the print  cartridge, and then reinstall it. See Print cartridge.
2 Install a new HP print cartridge.
3 Check the connection between the dc controller PCA (location J97) and the memory chip on the print cartridge (location J600).
4 Replace the memory chip cable and contact assembly.
5 Replace the dc controller PCA. See Dc controller PCA.

13.XX.YY DUPLEX JOB INTERRUPTED For help press  alternates with 13.XX.YY DUPLEX JOB INTERRUPTED  Discard top sheet and press or 13.XX.YY DUPLEX JOB INTERRUPTED Discard top two sheets and press

A duplex job was physically interrupted as the paper was momentarily routed to the output bin during duplexing. This error is usually caused by a user who is attempting to grasp the edge of the page as it exits the top output bin during the duplexing process.
1 Press ( HELP button) for more information.
2 Remove the specified number of pages from the output bin.
3 Press (SELECT button) to continue printing.
4 Replace the duplexer.
5 Replace the dc controller PCA. See Dc controller PCA.

NOTE If JAM RECOVERY =  OFF some pages will not be reprinted. Resend the missing pages.

13.XX.YY JAM For help press

A jam exists in the media path. 1 Press ( HELP button) for detailed information about clearing the jam.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 If the media is folding into an accordion shape, make sure that the shutter on the print cartridge opens as you insert the cartridge. Replace any defective print cartridge.
4 For information about how to resolve a jam, see the specific numerical error codes in this table.
5 See Paper-path troubleshooting in this chapter.

13.01.00. or 13.03.00JAM IN TRAY x For help press   or  13.03.00 Paper JAM open input trays then open and close top cover
A page is jammed in tray X. A 13.01.00 error message indicates that the media did not arrive at the pre-feed sensor (PS102) within the specified time.
A 13.03.00 error message indicates that the media did not arrive at the top-of-page sensor (PS103) within the specified time.

NOTE The 13.01.00 error can also be caused by the failure of the paper-level sensor (PS107). If this sensor fails, the lifter motor does not rotate to lift the paper tray plate.This error can also be caused when the printer attempts to pick up media from a tray that is empty, but the paper-out sensing mechanism for that tray has failed  and the printer senses that the tray appears to be loaded.
1 Press ( HELP button) for detailed information about clearing the jam.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Check that the paper-out sensor in the specified tray is functioning correctly.
4 Clean the pickup roller. If it is worn or damaged, replace it.
5 Clean the feed and separation rollers. If any of the rollers are worn or damaged, replace them (always replace both rollers at the same time).
6 Verify that the pre-feed sensor (PS102) is installed correctly. See Paper-feed assembly. 


13.01.00. or 13.03.00JAM IN TRAY x
For help press
or
13.03.00
Paper JAM open input trays then open
and close top cover
A page is jammed in tray X. 


A 13.01.00 error message indicates that the media did not arrive at the pre-feed sensor (PS102) within the specified time.
A 13.03.00 error message indicates that the media did not arrive at the top-of-page sensor (PS103) within the specified time. If the actions listed above do not resolve
the issue, continue with the following:

1 Open and close the specified tray while watching the control-panel display. A short delay should occur between when the tray closes and the tray-size message appears on the control-panel
display. If there is no delay and you do not hear the tray-lift motor lift the tray plate into place, replace the stack position sensor (PS107, PS802, or SR2) in the tray. See Printer switches and sensors, 500-sheet feeder switches, sensors, solenoids, and PCAs, or 1,500-sheet feeder switches, sensors, solenoids, and PCAs. 
2 Replace the tray X pickup solenoid.
3 Replace the tray 1 paper-pickup assembly. See Tray 1 paper-pickup assembly .

NOTE The 13.01.00 error can also be caused by the failure of the paper-level sensor (PS107). If this sensor fails, the lifter motor does not rotate to lift the paper tray plate. 
This error can also be caused when the printer attempts to pick up media from a tray that is empty, but the paper-out sensing mechanism for that tray has failed and the printer senses that the tray appears to be loaded.
4 Replace the paper-feed assembly. See Paper-feed assembly.
5 Verify that the top-of-page sensor (PS103) is operating correctly and that the sensor flag can freely move. Replace the sensor if it is not Operating correctly. See Printer switches and sensors.
6 Replace the dc controller PCA. See Dc controller PCA. 

 

13.21.00JAM IN TOP
COVER AREA  For help press

A jam exists in the top-cover area. 
A 13.02.00 error message indicates that the media did not pass the top-of-page sensor (PS103) within the specified time.
A 13.05.00 error message indicates that the media did not arrive at the fuser delivery sensor (PS108) within the specified time.
A 13.20.00 error message indicates that the printer power was turned on or that the printer attempted to initialize while the prefeed sensor (PS102), the top-of-page sensor (PS103) or the fuser delivery sensor (PS108) was detecting media.
A 13.21.00 error message indicates that the top-cover-open switch (SW101) was activated while a print job was printing (the top cover was opened or the switch is defective).
1 Press ( HELP button) for detailed information about clearing the jam.
2 Press ( UP ARROW button) and (DOWN ARROW button to step through the instructions.
3 Check the pre-feed, top-of-page, and fuser assembly sensors (PS102, PS103, and PS 108) and verify that the sensor arms move freely. (See Printer  switches and sensors.)
4 If the paper-feed assembly has been replaced, verify that the pre-feed  sensor (PS102) is installed correctly.See Paper-feed assembly.
5 Replace the top-of-page sensor (PS103). See Printer switches and sensors.
6 Replace the top-cover-open switch (SW101). See Printer switches and  sensors.
7 Replace the fuser. See Fuser.
8 Replace the dc controller PCA. See Dc controller PCA.
9 If this error message appears frequently, see Paper-path troubleshooting.


13.06.00 and 13.12.00 JAM INSIDE REAR
DOOR
For help press


A page is jammed near the rear output door.
1 Press ( HELP button) for detailed information about clearing the jam.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Check the paper-width and fuser delivery sensors (PS106, PS108) and verify that the sensor arms move freely. (See Printer switches and sensors.)
4 Check the inside of the duplexer for  scraps of media that might have torn off when a jam was cleared.
5 Replace the media-size sensor (PS106) and fuser. See Printer switches and sensors and Fuser.
6 Turn the power off. Remove the duplexer and turn the power on. If the error message persists, replace the dc controller PCA. See Dc controller PCA.
7 If the error message appears frequently, see Paper-path troubleshooting.

13.12.07
jam in stapler
NOTE: The stapler/stacker LED blinks in amber (this error applies to the stapler/ stacker only).


A jam exists in the staple cartridge (the stapler did not finish stapling but was able to return to its home position).
1 Press ( HELP button for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Remove any jammed paper from the stapler/stacker.
4 Remove the staple cartridge from the stapler unit.
5 Push the green door on the end of the staple cartridge up (in the direction of the arrows).
6 Remove the jammed staple.
7 Close the staple cartridge door. Replace the cartridge in the stapler unit.
8 Close the staple unit.
9 If the error persists, replace the staple cartridge.
10 If the error persists, replace the stapler unit. See To remove and replace the stapler unit.

13.12.08
jam in output device
NOTE: The stapler/stacker LED blinks in amber (this error applies to the stapler/ stacker only).


The output bin page-detection sensor has been active for longer than the specified time. 
1 Press ( HELP button) for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button)
3 Remove all of the pages from the output bin.
4 Open the jam-access door and remove all of the pages. Close the access door.
5 If this error message persists, replace the stapler/stacker.

13.12.09
jam in output device
For help press

NOTE: The stacker or stapler/stacker LED blinks in amber.


The stacker or stapler/stacker paper-inlet sensor has been active for longer than a specified time.
1 Press ( HELP button) for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Open the jam-access door and remove all of the pages. Close the access door.
4 If this error message persists, replace the stacker or stapler/stacker.

13.12.10
jam in output device
For help press
NOTE: The event log records this error message as 13.12.0A.
NOTE: The stacker or stapler/stacker LED blinks in amber.


A page did not arrive at the stacker or stapler/stacker paper-inlet sensor in the specified time.
1 Press ( HELP button) for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Open the jam-access door and remove all of the pages. Close the access door. 4 Verify that the output bin deflector (in the printer) is operating correctly.
5 If this error message persists, replace the stacker or stapler/stacker.

13.12.11
jam in output device
For help press
NOTE: The event log records this error message as 13.12.0B.
NOTE: The stacker or stapler/stacker LED blinks in amber.


A jam was detected when the stacker or stapler/stacker power was turned on.
1 Press ( HELP button) for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Remove all of the pages from the   output bin.
4 Open the jam-access door and remove all of the pages. Close the access door.
5 If this error persists, replace the stacker or the stapler/stacker.

13.13.00
JAM INSIDE DUPLEXER
For help press ?


A page is jammed inside of the duplexer. 1 Press ( HELP button) for detailed information about clearing the jam.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Check the inside of the duplexer for scraps of media that might have been torn off when a jam was cleared.
4 Turn the power off. Remove the duplexer and turn the power on. If this error persists, replace the dc controller PCA. See Dc controller PCA.
5 Replace the duplexer.

13.1C.00
FUSER JAM
For help press? 


A jam exists in the fuser area. The media is probably wrapped around the fuser roller.
1 Remove the fuser.
2 Turn the blue knob to remove the jammed media.
3 If necessary, replace the fuser. See Fuser.
13.98.00 open input trays then open and close top cover
The face-up tray was opened when the printer was attempting to send a page to the duplexer.
A page shorter than 200 mm (7.87 inches) was sent to the duplexer.
A page less than 120 mm (4.72 inches) in width was sent to the duplexer.
A multi-feed paper jam has occurred.
1 Remove any jammed media from the paper path.
2 Open and close the top cover.
3 Disconnect all optional paper-handling accessories.
4 Replace the feed and separation rollers. See Tray 2 feed rollers (this procedure includes the separation roller).
5 Replace the dc controller PCA. See Dc controller PCA. 

20 INSUFFICIENT MEMORY
For help press
alternates with
20 INSUFFICIENT MEMORY
To continue press


The printer has received more data from the computer than fits in the available memory.
1 Press ( SELECT button) to resume printing.
NOTE A loss of data will occur.
2 Reduce the complexity of the print job to avoid this error.
3 You might be able to print pages that are more complex if you add memory to the printer.

21 PAGE TOO COMPLEX
For help press
alternates with
21 PAGE TOO COMPLEX
To continue press

The printer cannot process the page quickly enough.
1 Press ( SELECT button) to process the page.
NOTE A loss of data will occur.
2 Make the page contents less complex and re-send the print job.

22 EIO X
BUFFER OVERFLOW
To continue press


The printer's EIO card in slot X has overflowed its I/O buffer during a busy state.
1 Press ( SELECT button) to resume printing.
NOTE A loss of data will occur.
2 Check the configuration of the EIO card and the host computer.
3 If this error message persists, replace the EIO card.

22 PARALLEL I/O
BUFFER OVERFLOW
For help press
alternates with
22 PARALLEL I/O
BUFFER OVERFLOW
To continue press


The parallel buffer has overflowed during a  busy state.
1 Press ( SELECT button) to resume printing.

NOTE A loss of data will occur.

2 Check the parallel I/O configuration. Set HIGH SPEED to NO and ADVANCED FUNCTIONS to OFF.
3 Replace the formatter PCA. See Formatter assembly .

40 EIO X BAD
TRANSMISSION
To continue press 

A connection with the card in EIO slot X has been broken abnormally.
1 Press ( SELECT button) to resume printing.
NOTE A loss of data will occur.
2 Check that all of the cables are connected to the EIO ports and that the EIO board is seated properly.
3 If possible, print to another network printer to verify that the network is working properly.
4 Check the configuration of the EIO card.
5 If this error message persists, replace the EIO card.

41.3 UNEXPECTED
SIZE IN TRAY XX
For help press
alternates with
41.3 UNEXPECTED
SIZE IN TRAY XX: [TYPE] [SIZE]
For help press


The media that is loaded is longer or shorter in the feed direction than the size that is configured for the tray.

1 If the incorrect size was selected, cancel the job or press ( HELP button) to gain access to help.
2 Press ( UP ARROW button) and (DOWN ARROW button to step through the instructions.
3 Print a configuration page and verify that the tray settings match the media in the tray. See Configuration page.
4 Verify that the pre-feed, top-of-page, and fuser delivery sensors (PS102, PS103, PS108) are operating and the sensor flags can move freely. See Printer switches and sensors.
5 Replace the dc controller PCA. See Dc controller PCA.

41.X
PRINTER ERROR
For help press
alternates with
41.X
PRINTER ERROR
To continue press


A printer error has occurred.
X Description
1 unknown misprint error
2 beam-detect misprint error
4 no VSYNC error
7 feed-delay error
9 signal-noise error
1 Press ( SELECT button) to continue orbpress ( HELP button) for more information.
2 If the message persists, turn the printer power off and then on again.
3 If these errors becomes a frequent problem, replace the dc controller PCA. See Dc controller PCA.

49.XXXX
PRINTER ERROR 


To continue turn off then on  A critical firmware error has occurred that caused the processor on the formatter to abort the operation.
This type of error can be caused by invalid print commands, corrupt data, or invalid operations. In some instances, electrical noise in the  cable can corrupt data during transmission to the printer. Other causes include poorquality parallel cables, poor connections, or specific software programs. Sometimes, the formatter itself is at fault, which is usually indicated by a 79 Service Error.

1 Press CANCEL JOB to clear the print job from the printer memory.
2 Turn the printer off and then on.
4 Try printing a job from a different software program. If the job prints, go back to the first program and try printing a different file. If the message appears only with a certain software
program or print job, contact the software vendor for assistance.

5 If the message persists when using different software programs and attempting specific print jobs, disconnect all cables that connect the printer to the network or a computer.
6 Turn the printer off.
7 Remove all memory DIMMs or thirdparty DIMMs from the printer. (Do not remove the firmware DIMM in slot J1.) See Firmware DIMM (LJ 4200/4300 only).
8 Remove all of the EIO devices from the printer.


49.XXXX
PRINTER ERROR
To continue turn off then on


A critical firmware error has occurred that  caused the processor on the formatter to abort the operation.
This type of error can be caused by invalid print commands, corrupt data, or invalid operations. In some instances, electrical noise in the cable can corrupt data during transmission to the printer. Other causes include poorquality parallel cables, poor connections, or specific software programs. Sometimes, the formatter itself is at fault, which is usually indicated by a 79 Service Error. After performing the actions above, procede with the following:
1 Turn the printer on.
2 If the error message disappears, reinstall each DIMM and EIO device individually, making sure to turn the printer power off and then on again as you install each device. To replace a DIMM, see Firmware DIMM (LJ 4200/4300 only). 
3 Replace the DIMM or EIO device that caused the error message.
4 Remember to reconnect all of the cables that connect the printer to the network or computer.
5 If this error message persists, replace the firmware DIMM. See Firmware DIMM (LJ 4200/4300 only).
6 Replace the formatter assembly. See Formatter assembly

49.24.02 
printer error


The printer has experienced a critical error. 1 Verify that the ribbon cables are fullyseated in the connectors on the dc controller PCA.
2 Replace the power-supply assembly.See Power supply.
3 Replace the dc controller PCA. See Dc controller PCA.
4 Replace the formatter assembly. See Formatter assembly

50.X FUSER ERROR
For help press


A fuser error has occurred. X Description
1 low fuser temperature
2 fuser warmup service
3 fuser over temperature
4 faulty fuser
5 incorrect fuser is installed
6 open fuser circuit
1 Turn the printer off and allow it to cool down.
2 Verify that the correct model of fuser is installed.
3 Verify that the correct voltage fuser is installed.
4 Reinstall the fuser, and check the connection between the fuser and the printer. Replace the connector if it is damaged.
5 Replace the fuser.
6 Replace the dc controller PCA. See Dc controller PCA.
7 Replace the power-supply assembly. See Power supply.

51.XY
PRINTER ERROR
For help press
alternates with
51.XY
PRINTER ERROR
To continue turn off then on
A printer error has occurred.


X Description
1 beam-detect error
2 laser error
1 Press ( SELECT button) to continue.
2 Turn the printer off and then on.
3 Reseat the connectors between the laser/scanner and dc controller PCA (J83 and J84).
4 Replace the laser/scanner assembly. See Laser/scanner assembly.
5 Replace the dc controller PCA. See Dc controller PCA.

52.XY
PRINTER ERROR
For help press
alternates with
52.XY
PRINTER ERROR
To continue turn off then on
A printer error has occurred.


X Description
0 scanner error
1 scanner startup error
2 scanner rotation error
1 Press ( SELECT button) to continue.
2 Turn the printer off and then on.
3 Reseat the connectors between the laser/scanner and dc controller PCA (J83 and J84).
4 Replace the laser/scanner assembly. See Laser/scanner assembly.
5 Replace the dc controller PCA. See Dc controller PCA.

53.XY.ZZ
PRINTER ERROR
To continue press cancel job


An error occurred in the printer memory.
X DIMM Type
0 ROM (firmware DIMM)
1 RAM 
Y Device Location
1 DIMM Slot 1
2 DIMM Slot 2
3 DIMM Slot 3
4 DIMM Slot 4
ZZ Error Number
0 unsupported memory
1 unrecognized memory
2 unsupported memory size
3 failed RAM test
4 exceeded maximum RAM size
6 invalid DIMM speed
Press CANCEL JOB. If the problem persists, replace the DIMM card in the specific slot. See Firmware DIMM (LJ 4200/4300 only

54.1
Remove the sealing tape from toner cartridge

The print cartridge was installed with the sealing tape in place.
1 Remove the sealing tape from the print cartridge.
2 Replace the print cartridge.

55.X
PRINTER ERROR
For help press
alternates with
55.X
PRINTER ERROR
To continue press


The dc controller is not communicating with the formatter. The problem could be caused by a timing error or an intermittent connection.
1 Press ( SELECT button) to continue.
2 Turn the printer off and then on.
3 Reseat the connectors between the dc controller PCA and the formatter.
4 If the problem persists, replace the dc controller PCA. See Dc controller PCA.
5 Replace the formatter. See Formatter assembly .
56.1 printer error To continue turn off then on An unknown input device is installed. 1 Turn the power off and then on.
2 Reinstall all input trays.
3 Remove all non-HP paper-handling devices.

56.2 printer error To continue turn off 
then on


An unknown output device is installed. 1 Turn the power off and then on.
2 Reinstall the stacker or stapler/stacker.
3 Remove all non-HP paper-handling devices.

57.X A printer fan is not functioning. Turn the printer off and then on.

PRINTER ERROR
To continue turn off then on
or
57.3 EP fan failure
or
57.4 main fan failure


X Description
3 Cooling fan, right side (LJ 4250/4300/4350 only) 4 Main cooling fan, left side
57.3 Cartridge fan error (F2)
1 Reconnect the connector between the fan and the dc controller PCA (location J78).
2 Replace the fan. See Cooling fan, right side (HP LaserJet 4250/4300/4350 Series printers only).
3 Replace the dc controller PCA. See Dc controller PCA.
57.4 Main fan error (F1)
1 Reconnect the connector between the fan and the power supply.
2 Verify that the ribbon cables are fully seated in the connectors on the dc controller PCA.
3 Replace the fan. See Main cooling fan (left side).
4 Replace the power-supply assembly.See Power supply.
5 Replace the dc controller PCA. See Dc controller PCA.
57.7 duplex fan failure The cooling fan in the optional duplexer is not functioning.
1 Turn the printer off and then on.
2 Replace the duplexer.

58.X
PRINTER ERROR
For help press
alternates with
58.X
PRINTER ERROR

To continue turn off then on A memory error has been detected.
X Description
2 air-temperature sensor
3 Dc controller
4 power supply
Turn the printer off and then on.

58.2 Air-temperature sensor
1 Turn the printer off and then on.
2 Reconnect the connector between the air-temperature sensor (the bar mounted across the main cooling fan on the left side of the printer) and the power supply (location J63).
3 Replace the air-temperature sensor. See Main cooling fan (left side).
4 Replace the power-supply assembly. See Power supply.

58.3 Dc controller
1 Replace the dc controller PCA. See Dc controller PCA.

58.4 Power supply
1 Replace the power-supply assembly. See Power supply.

64
PRINTER ERROR
For help press
alternates with
64
PRINTER ERROR
To continue turn off then on


A scan-buffer error has occurred. 1 Turn the printer off and then on.
2 If the message persists, replace the formatter assembly. See Formatter assembly .

66.00.15
EXTERNAL DEVICE FAILURE

NOTE: The stacker or stapler/stacker LED is off.
The stacker or stapler/stacker was removed and then replaced while the printer power was on.
1 Turn the printer power off.
2 Verify that the stacker or stapler/stacker is installed correctly.
3 Turn the printer power on. 

66.12.XX
output device failure
For help press


NOTE: The stacker or stapler/stacker LED is continuously illuminated in amber. A stacker or stapler/stacker error has occurred.

XX Description
01 output-lift roller or paddle motor error
02 jogger-motor error
03 stapler-motor error
1 Press ( HELP button) for detailed information.
2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions.
3 Turn the power off.
4 Verify that the stapler/stacker is installed correctly and that its electrical connector is seated in the connector on the printer.
5 Turn the power on.
6 If the error 66.12.03 persists, replace the stapler unit. See To remove and replace the stapler unit.
7 If other errors messages persist, replace the stacker or stapler/stacker.

68.X
PERMANENT STORAGE ERROR
For help press
alternates with
68.X


One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to the factory default. Pressing ( SELECT button) should clear the message. Printing can continue, but the printer might behave unexpectedly in response to the changed settings.
X Description
1 Press ( SELECT button) to continue.
2 Turn the printer off and then on.
3 Check the printer settings to determine which settings have been changed. See Settings and defaults and Controlpanel menus.
4 Perform a NVRAM initialization. See NVRAM initialization.

PERMANENT STORAGE ERROR
To continue press 
0 onboard NVRAM


1 flash DIMM or hard drive
5 Replace the formatter assembly. See Formatter assembly .

68.X PERMANENT
STORAGE FULL
For help press alternates with

68.X PERMANENT
STORAGE FULL
To continue press


A nonvolatile storage device is full. 
Pressing (SELECT button) should clear the message. Printing can continue, but the printer might behave unexpectedly in response to the changed settings.
X Description
0 onboard NVRAM
1 flash DIMM or hard drive
1 Press ( SELECT button) to continue.
2 For 68.0 errors, turn the printer off and then on.
3 If a 68.0 error persists, Initialize NVRAM. See the caution and note in To initialize NVRAM.
4 For 68.1 errors, use the HP Web Jetadmin software to delete files from the disk drive.
5 If this error message persists, replace the formatter assembly. See Formatter assembly .
6 If the 68.1 error persists, reinitialize the hard disk. See the caution and note in To initialize the hard disk.
7 If the 68.1 error persists, replace the disk.

68.X PERMANENT
STORAGE WRITE FAIL
To continue press


A nonvolatile storage device is failing to write. Pressing (SELECT button) should clear the message. Printing can continue, but the printer might behave unexpectedly in response to the changed settings.
X Description
0 onboard NVRAM
1 removable disk (flash or hard)
1 Press (the SELECT button) to continue.
2 Turn the printer off and then on.
3 If the 68.0 error persists, initialize the NVRAM. See the caution and note in To initialize NVRAM.
4 If this error message persists, replace the formatter assembly. See Formatter assembly .
5 For a 68.1 error message, reinitialize the hard disk. See the caution and note in To initialize the hard disk.
6 If the 68.1 error persists, replace the disk.

69.X
printer error
To continue turn off then on


The optional duplexer is not functioning
. 1 Remove the duplexer.
2 Turn the printer off and then on.
3 Replace the duplexer.
4 If the message persists, replace the duplexer.

79.XXXX
PRINTER ERROR


A critical hardware error has occurred
1. Turn the printer off and then on.
2 If the problem persists, reseat the firmware DIMM.
3 Reseat the formatter.
5 Replace the formatter. See Formatter assembly .
6 Replace the firmware DIMM. See Firmware DIMM (LJ 4200/4300 only).

8X.YYYY
EIO ERROR


The EIO accessory card in slot X has encountered a critical error.
1 Turn the printer off and then on.
2 If the problem persists, reseat the EIO card.
3 Replace the EIO card.
4 Replace the formatter assembly. See Formatter assembly .

 

     

HP Printer Repair

 

Please publish modules in offcanvas position.