• HP Printer Repair La Mirada, California

    HP Printer Service La Mirada, California

  • hp printer repair near me Irvine, CA

    HP Printer Repair Near Me Irvine, CA

  • Onsite HP Printer Repair Santa Fe Springs, California

    Onsite HP Printer Service in Santa Fe Springs, Ca

  • hp laserjet printer repair pasadena

    HP Printer Service Center in Pasadena, California

  • HP Printer Repair City of Industry - Walnut, California

    Printer Repair in Walnut, CA and Industry, California

  • Onsite Printer Repair in Brea, California

    Brea California onsite printer repair services

  • Commerce, California onsite Printer Repair

    Commerce, CA onsite printer service company.

HP LaserJet Enterprise MFP M630 Fuser Error 50


50. Error Messages
Fuser error 50 To continue turn off then on
Classification
The fuser assembly has suffered a malfunction.
W = fusing assembly error value, X = fuser mode, Y = previous printer sleep state, Z = next hp laserjet printer sleep state

Appropriate remedy

50.1 Fuser Error
50.2 Fuser Error
50.1 Fuser Error or 50.2 Fuser Error
Low fuser temperature 1 or fuser warm-up failure
1. Reseat the fuser. Check the connecting adapter (J128) involving the fuser assembly along with the hp printer. If it is damaged, exchange the fuser assembly.
2. 50.1 Fuser Error: rejoin the connector (J82) is located on the DC controller PCA.
-or-
50.2 Fuse Error: rejoin the connection (J53, J54 and J82) is located on the DC controller PCA.
3. Change the fuser.
4. Fuser Error 50.2: rejoin the connection (J62) within the low-voltage power supply PCA.
5. In the event that the issue persists, swap the low-voltage power supply.

50.3 Fuser Error


High fuser temperature 1
1. Reseat the fuser. Take a look at the connection (J128) regarding the fuser along with the hp printing device. If it is stressed, swap out the fuser.
2. Rejoin the connection (J82) along the DC controller PCA.
3. Try to replace the fuser.
4. In the event that the error remains, switch the LVPS (Low Voltage Power Supply).

50.4 Fuser Error / Fuser Error 50.4

Drive circuit fault
1. Check the energy source. Be sure the power matches product requirements.

NOTE: In case the power provider cannot fulfill the power frequency prerequisite of 40 to 70Hz, the fuser temperature control will not PERFORM accordingly and leads to this malfunction.

2. Reseat the connector (J53) within the DC controller PCA.
3. Provided that the error lingers, swap out the LVPS (Low Voltage Power Supply).

HP LASERJET ENTERPRISE M630 MAINTENANCE KIT

 

50.7 Fuser Error / Fuser Error 50.7
Fuser pressure-release mechanism failure
1. Reload the fuser assembly. Examine the connector (J128) between the fuser assembly along with the printer. If it is impaired, change out the fusing assembly.
2. Search the fuser pressure-release sensor flag. If it is broken, try replacing the fuser.
3. Reseat the connection (J221) of the fuser motor and the connector (J89) on the DC controller PCA.
4. Utilize fuser motor (M299) drive test inside the component test to check that the fuser motor is adequately performing. If it isn't, change the fusing assembly motor.
5. Change the fuser assembly.

50.8 Fuser Error
Low fuser temperature 2
1. Reload the fuser assembly. Check out the connected adapter (J128) concerning the fuser assembly and the hp printing device. If may be damaged, replace the fuser.
2. Rejoin the connection (J54) on the DC controller PCA.
3. Remove and replace the fuser.
4. Reattach the connection (J62) on the(LVPS) Low Voltage Power Supply PCA.
5. Provided that the error continues, swap the LVPS (Low Voltage Power Supply).

50.9 Fuser Error
High fuser temperature 2
1. Reload the fuser. Check out the connection (J128) anywhere between the fuser assembly as well as the printers. If it is broken, switch out the fuser.
2. Rejoin the connection (J54) on the DC controller PCA.
3. Try replacing the fuser assembly.
4. Reconnect the connection (J62) within the LVPS (Low Voltage Power Supply).
5. In the event that the error persists, swap out the LVPS (Low Voltage Power Supply).


Create On-site HP Laserjet Printer &
HP Color Laserjet Printer Service Appointment Online


You're invited to fill out form below and someone from our Support Group will contact you to confirm.   You may also fill out form to ask a technical question or make comments.

 

 
Hours of Operation

Monday       9:00am - 5:00pm
Tuesday      9:00am - 5:00pm
Wednesday 9:00am - 5:00pm
Thursday     9:00am - 5:00pm
Friday          9:00am - 5:00pm
Saturday      Closed
Sunday        Closed

     

 
Follow us on Social Media

Onsite Printer Repair

Printer Repair

Laserjet Printer Repair

printer repair near me

We Accept the Following forms of Payment

Onsite HP Printer Service

 


Customer Care Representative
(888) 276-4666  Toll Free

Whittier:
W. Whittier Blvd.  California 90605
Santa Ana:
S Main St. 
Santa Ana, CA 92707
Long Beach:
Long Beach Blvd, Long Beach, CA 90802